Environment

Comment Subscribe to comments with RSS. CampRicco I have two battery banks. I want to be able to plug portable bank into stationary bank for charging. Should I be concerned about the inrush current when connecting portable bank into stationary bank while battery charges are equalizing. Can a resistor be added to cable to slow current while banks are equalizing. If so where in connection and what value would you recommend. The two battery packs you have are of different capacity, so you are creating a situation where batteries are going to get overcharged. I would recommend charging them separately. My question is can I use 1 battery for my outboard for a 12 volt starting and charging system without disconnecting the 2 batteries.

ISP TECHNOLOGIES

The transistors and diodes are available from many sources. Please visit the Parts reference page for suggested sites. Bally Game List.

Jumper cables are not designed to carry the huge surge of electrical current, and will quickly heat up to very high temperatures. This can melt the insulation on the cables and potentially expose people to direct contact with the electrical cables. The heat can also melt solder and other components that hold the cables and clamps together.

Easily Remove Spills Peter woke up after the annual office Christmas party with a pounding headache, cotton-mouthed and utterly unable to recall the events of the preceding evening. After a trip to the bathroom, he made his way downstairs, where his wife put some coffee in front of him. Was it as bad as I think? You succeeded in antagonising the entire board of directors and you insulted the Chairman of the company, right to his face”. The scandal was begun when a 21 year old woman, known only as Mary, claimed that she had given birth to God’s “only son” last week in a barn in the hamlet of Bethlehem.

Sources close to Mary claim that she “had loved God for a long time” that she was constantly talking about her relationship with God, and that she was “thrilled to have had his child”.

Battery Bank Tutorial: Joining Batteries Via Series or Parallel for Increased Power

It shows on the picture by the two AC outputs 7 and 8. I cannot find a download for the manual so I cannot confirm that both of these AC outputs are milliamps but this is what it looks like from the data on their website. Will this damage the unit? The amp comes with FX loop but currently my new setup is running everything upfront. I only want to gate my drive pedals and vibe.

Connecting the jumper cables the wrong way might actually damage your vehicle. If your battery is running low (that’s why you can’t start) then you have less voltage across it’s nodes. When you connect another battery with the exchanged nodes, the current will flow out of your battery (since it’s voltage is lower) and damage the battery.

I mean, bios was frozen at startup, no moniter, drives, no usb nothing, and then the eraser. If you live in FL I owe you a beer. What does FL stand for? I live in Mauritius. It’s such a nice country. Other side of the world from the land of the Dodo I’m afraid. Unfortunately, i’m still stuck. I had the same problem no usb, monitor etc. At first I powered down, bled power and it would get to the “Sorry, windows did not shut down

Chevrolet Uplander Owner’s Manual

How to Hook up Jumper Cables Your car battery could be too weak to start your car for a number of reasons: Whatever the cause, you can use jumper cables to connect your dead battery to a live vehicle battery of the same size. The live battery then charges your dead battery enough to get the car started again. Steps 1 Park the donor vehicle live battery next to the vehicle with the dead battery.

Position the vehicles so that the batteries are as close together as possible, but make sure the two cars do not touch. Set the parking brakes, and switch each car into park or neutral for automatic or manual transmissions, respectively.

Jun 17,  · I recently learned that there is an orange relay with a diode inside that protects the ECU from reverse-voltage if the battery or jumper cables are hooked up wrong. I don’t know if the TCU (automatic) is also protected this way but knowing Nissan it probably is.

Hardware Abuse Some of the things people do to computers is downright painful. Recently, I got a call from someone who turned off his computer whenever he found himself somewhere in Windows he didn’t want to be. Wonder of all wonders, scandisk found a score of lost allocation units and bad sectors. He called about a week later and said that it would no longer boot up. He brought it in, and I discovered that sixteen nicely drilled holes were in the bottom of the case.

I asked him about it, and he said the machine was too hot sitting on his lap, so he had drilled these “air holes. I once had a customer that wanted a light in her computer, similar to a computer she saw at one of her friend’s houses. So she lit a candle and set it inside her tower case. One of my favorite stories is from back in the 90s. A guy bought a bit sound card for his computer, but for whatever reason decided he only needed an 8-bit sound card. Instead of taking it back and exchanging it, he figured all he needed to do was get a pair of scissors and physically cut the sound card in half.

My friend from school thought that since the CPU heatsink burned his finger when the computer was on, it must be keeping the CPU too hot to overclock. So he took it off.

ISP TECHNOLOGIES

This new version of the software 1. Transverter support, Dual RX and wider bandscope bandwidth support are just a few big changes! Note that this page will always be a work in progress

RAY: By the way, they now sell “idiot-proof” jumper cables that won’t operate if you hook them up incorrectly. Go out and buy two pairs. King Features Syndicate.

Ask Question Step 5: Cut and Prep Extension Cords On each extension cord cut off the plug end leaving the maximum available length to the socketted end of the cord as it will possibly have to go to the top of the tree. On the cord split the ends of the wire apart by cutting the thin piece of plastic holding the two wires together. Use a Sharpie marker on each end socketted end of the cord to write the numbers 1 through 8 so that you can easily identify which socket goes to which channel on the SSR module.

We will also need one plug and also some extra wire for the next step, so either cannibalize a 9th extension cord or leave some extra room on the 8 extension cords when cutting off the plug end. Add Tip Ask Question Step 6: Since the amount of wires here can get cluttered very easily I used a power distribution bock and a staple gun to try and keep everything in place.

With power off, take the cut up plug end from the previous step and plug it to the power strip. Strip the other two ends and connect each to the top and bottom power distribution block and staple these two connections down.

Tech Stuff – LAN and Telephones

My symptoms are no power to speak of below rpm. At that point turbo boost occurs and power comes up, though no where near what it should be. The engine revs smoothly but runs out of steam before rpm. I’m left to decide if the problem is the AMM or the O2 sensor. If your B FT throws oil around like mine, the throttle body can easily get crudded up and cause problems exactly as you described. All these were fine, just a dirty throttle body caused the problem.

Hooking up jumper cables in the backwards has the potential to cause an explosion. The reaction occurs if hydrogen gas builds up around the battery and a spark ignites the gas. The correct way to apply jumper cables is to attach the red end to the positive terminal of the dead battery first, then the other red end is attached to the positive terminal of the charger battery.

AB, I have a hp dv that I would like to add extra memory to and have no bloody clue how to do so step by step after oppening the memory cover. There are two memory slots under the memory cover. Carefully spread latches located on both sides of the module. The memory module will pop up at a degree angle. Pull the memory module from the slot by the edges. As an example, you can use this guide for removing RAM modules. I purchased an extra gig for the laptop and it seems not to fit as it is a long strip.

I guess you purchased memory for a desktop computer. The laptop module is shorter. I read that in order to upgrade from the current 1 gig to 2, I need to purchase two 1 gig slots because this laptop does not have extra slots. I would have to remove the current pieces and insert the news ones.